Mazak QT8N offset sharing between programs
Hello! finally after reading through this site for years I have an issue I need help with. 1993 Mazak QT8N. T32-2 control. I added the EIA/ISO option. I do not have the programming manuals. I bought...
View ArticleClik here to view.
T32 -6 CMT transfer
Hey guys, I'm having drama's getting my MP630 to transfer programs. I've tried a few different parameter sets and cable configs, and the best i can get is "q" and a diamond shape (as per below) through...
View ArticleQT15N with Mazatrol T32B, need help to fix errors
Hey Mazak guys, I recently bought a QT15N with Mazatrol T32B control that came without any manuals though thankfully I found some of them on this forum. I haven't been able to get it to work yet...
View ArticleQT15N with Mazatrol T32B, need manuals
Hi Mazakers, I recently bought a QT15N with Mazatrol T32B control that came without any manuals. It would be great if anyone could send me the operating manual for the lathe. Thanks in advance
View Articleprogramming manual mazak sqt 15m markII needed
Hello everyone, I got a machine, a mazak sqt 15m markII that came with I think almost all the manuals but no programming manual does someone have It? thanks In advance. some other questions, can there...
View ArticleMazak Multiplex 6200-II Y
No one at my job can tell me how to teach a tool on the X-axis using the tool eye sensor? It's a "live tool" 1/8-27 NPT carbide thread mill that...
View ArticleClik here to view.
connecting three-phase power cable from the power grid to the Mazak transformer
Hello! I have a question. The three-phase power cable from the power grid is written on the transformer switch where I need to connect the L1, L2 and L3 wires, but where I need to connect the N Null...
View ArticleHCN mazak 6800 automate artifact
We have a FMS system with 4 hcn 6800's , We run an artifact on these machine weekly to determine the state of the alignment. Right now the operators manually do this, which shuts off production. We are...
View ArticleMatrix 2 tool probe parameters
Working to re calibrate the tool setter on a VCU 500A 5X after a crash left the B-Axis home position off thus effecting the tool setter. Probe pad has been adjusted flat once again, now i just need to...
View ArticleSQT18M T32 Counter Balance Pressure
Does anyone know what the counter balance pressure should be set at? I'm getting some strange intermittent axis loads and I suspect it could be a hydraulic issue, when I clamp / unclamp the chuck the...
View ArticleClik here to view.
Dirty Oil on the circuit board
Hello! I have oil on many circuit boards, like in the pictures Does the oil affect the electronic boards? I cleaned some boards with distilled water and so far I have not found traces of burning from...
View ArticleIntegrex mill spindle orient position problem
I have had problems randomly with my mill spindle orienting to the wrong position. It may work fine for a week or month or sometimes it may do it 2 or 3 times a day. Unfortunately it has only done it...
View ArticleSetting Z offset on Smooth Control
We recently installed a new Mazak HCN 8800 with smooth control, replacing our old FH880 with M+ so quite a good upgrade. Having a little difficulty in setting the Z work offset however, clearly it`s...
View ArticleVTC-16B questions
I am (perhaps foolishly) looking at a VTC16b. It would end up going in my garage, so it's a bit ambitious size wise I know. The adder is that it's currently non-functional (supposedly CRT driver board...
View ArticleClik here to view.
1999 Mazak QT 18 with tplus Turret position off
Hi i had a tool hit the chuck during a tool change. Fortunately, the spindle was not running, and nothing appeared to be broken. However, as you can see from the picture tool position is way off from...
View Articlebarely know Mazatrol, but need a test program
I barely know anything from Phils videos and Believe me have watched them. I am getting ready to close a good deal on a Mazak with subspindle and live tooling MAZAK SQT-18MS. Problem is I need a...
View ArticleClik here to view.
Slide Lube Alarm - Oil Pressure Sensor
Hey guys, I have a QT15 which is throwing a slide lube alarm and preventing me from running programs. If I disconnect this sensor (see image) the alarm goes away. The pump motor is running and if I...
View ArticleSlant Turn 28 atc mc
i am going to be looking at a slant turn 28 atc mc t3 control. How do you tell what options it has like if it has full C axis, iso, Dnc ect. Thanks
View ArticleNeed advice for moving a mazak M4 lathe
Looking at buying an old m4 lathe, and having had a couple of bad experiences moving machinery, was wondering if anyone had any experience rigging one of these?
View ArticleM codes don't execute, QT15N with a T32B control
Hi Mazakers, I have a Hyundai QT15N with a T32B control. A problem I have is that it doesn't execute M codes. Nothing happens when I add an M code process in a Mazatrol program. For example, I can...
View Article