mazak qt15 rapid parameter
ive looked for which parameter effects the rapid speeds and cant seem to find anything. ive already altered the chuck paramater to my liking , just not sure which one i need to deal with on the rapid....
View ArticleMazak FJV 25 manual
Does anyone have a manual for a FJV 25? I am looking for a picture of the spindle/z assembly and what Belleville washers the spindle takes. Thanks!
View ArticleThread Tool Definition - The Basics (T2)
Alright, this is my first time single point threading the OD of a part on the T2. I'm having some trouble reconciling how I've set the Z-offset of my top notch insert and what I see on the trace...
View ArticleClik here to view.
Does anyone have CAMate 3 INTERCIM module interface ?
any experience with this interface ? ? i have an integrex from early 2000 and it came with this interface can this really do CAM ? Attached Thumbnails Â
View ArticleMazak back chamfering
Hello all, I am running a 1996 Mazak V-515/40 with an M-plus controller. I have a issue with this machine and I am interested in trying something but not sure how to do it. First of all... the issue I...
View Articlemazak change language
I know how to change the language go into parameters then machine parameters change k11 only now when i press parameters the next ket to machine parameters is not showing in the usuall position, i have...
View ArticleClik here to view.
B-axis Continuous Live Turning in Mazak Integrex i200
I have a Mazak Integrex i200. We are trying to do continuous B-axis OD turning. Currently developing a new postprocessor for this machine. Does anybody have an EIA sample for B-axis live turning? Any...
View Article2019 Mazak 350 my Milling parameter help
Hello, I have a 2019 Mazak QTU 350 MY. I am wondering if anyone knows the parameter to change so that the chip conveyor does not start when the cycle start button is hit? Thank you in advance.
View Articlemazatrol cam t-2
hello, i have a mazatrol cam t-2 and i use mastercam but i don't have a post processor i need for help and i am waiting for a favorite answer thanks a lot
View Article1993 qt15( 202 low hydraulic alarm )
hello 1993 qt15 t-32 keep getting a 202 low hydraulic red alarm can turn machine on and off and will clear it for a couple of parts then will pop back up and wont clear pressure switch is a little low...
View ArticleClik here to view.
2014 never used Mazak QT Smart 100S won't boot up mystery...
Pressing control start button brings up screen below but it never goes past that. Mazak tech convinced the lithium battery at the LCD rear was low but it measures full 3 V. I hesitate to even mention...
View ArticleFusion 640M: Keep spindle on in manual mode
When switching from MDI to handwheel after executing S1000 M3, the spindle stops, effectively preventing me from doing any quick manual work. Is there a parameter to bypass this behavior?
View ArticleMazak multiplex with mazatrol t plus control. brain explosion.
Hello empire. I'll start this post by playing on skip.)): nopity: We have acquired a super double-spindle machine with a flex fl100s robot. He's not working very well: nutter:, we are now treating him....
View ArticleMazak Varixis 500 floor prep, to lag or not to lag?
Hello, We are looking at installing a used Mazak Variaxis 500, mid 2000's, pallet changer. Will these run without an isolated slab and anchored? We have a VCU-400 5 axis, ya, those have to be laged but...
View ArticleMazak FH 8800: calculations for new work offset based on a relative work offset
Hi all We have 4 axis FH 8800 Mazak machine with B as a rotary axis. I have noticed that the machine able to assign a new work offset coordinate based on another existing work offset. For example, take...
View ArticleMazak QT20N--T2 lost parameters and has blinking light on monitor.
Hello all I am new in machining and have purchased a QT20n with a T2 controller, the machine powers up and only has a blinking light on the screen, nothing else works. I called a guy to come look at it...
View ArticleMazatrol - Machining with C-axis brake rather than clamp?
As title suggest, is it possible to run with C-axis brake by adding M-codes in the operation? Currently running a small part with 72 threaded holes around the OD, and by milling/drilling/chamfering and...
View ArticleQT-10, T2-CAM, Troubleshooting X & Z axis drive not ready (TR8A-L & TR43B)
I started this post, realized I had written a novel, so I made the short version and I'll reply below with more detail. I'm looking for troubleshooting information for the TR8A-L servo drive, TR43B...
View ArticleMazak T1 boring bar retract clearance parameters
Trying to get more room to fit a boring bar in a hole. I've reduced PX1 as small as it will go without error (51 units) but there seems to be another small move there too. Is there anything else i can...
View ArticleClik here to view.
Re-Home Turret QTN 250msy Nexus 640T
Hi Guys, I got this alarm on switch on this morning. "378 Battery Malfunction (Turret)" So I managed to change the battery in the MR2J drive after watching a video of someone doing similar. Power on...
View Article