"mazak super turbo x 48 mk ii"
Hi and hello friends, My name is sreerenj,from india.this is my first post in this forum. This is regarding an enquiry for a software for offline programming in my "MAZAK SUPER TURBO X 48 MK II" .we...
View ArticleQT-8 alarm 128 Emergency stop
Fired up the control and got alarm 128 emergency stop, manual says emergency stop button pushed. Reset the E stop and restarted control and can't clear alarm. Dragging out the wiring diagram now just...
View ArticleScam? Too good to be true?
Mazak Qt 15 CNC Lathe | eBay He has a newer QT20 for cheap as well. Looking at his feedback just a few justin beeber tickets. Could be a great deal...could be a dud.
View ArticleGroove option 4 not cutting part off
Using groove option 4 (part off with a corner chamfer) isn't cutting the part off completely. The control will not allow a negative number in the final point X and there is no option in the TPC to...
View ArticleT-Plus Program and Operation question
I had a simple part to turn-- 75mm long, 30mm diameter in the middle and each end is turned to 15mm back 12.5mm. Center and 1/4-20 tapped hole in one end. The 30mm dia was left 0.1mm heavy for grinding...
View ArticleNecking or FR/MIN Grinding Allowance Question
I'm reading through my programming manual, and I really don't understand what this Necking or FR/MIN is about. Can anyone give me the "complete idiots" rundown of what this is referring to? BTW.....I...
View Articlehoming problem
Well, after leaving a job with an old Mazak, I have a friend with a lathe, not sure of model (he is getting back to me) about a 2000-2001 with sub spindle, live tooling, and y axis. When homing,...
View Articlemazatrol cam m2 computer connection
hello, ı have a machine mazak vqc 20/40b mazatrol cam m2 control unite. I do not know how to link the computer with which parmetreler change, and how to be prepared by a cable, Can you help?
View ArticleRunning VQC 15/40 being parted out
I am working with a small shop that was in the process of purchasing a pair of running Mazak VQC-15/40 mills. That was until the ham fisted maint guy started riping the first machine apart suitable for...
View Article86 QT10N ATC m/c live tooling collets, what are they ?
I have a wonderful Mazak turning center, slow, but cuts tough and has fantastic finishes. Only problem, the original V and H live tooling holders don't have the collets. I was told they are ER25, but I...
View ArticleClik here to view.
Alarm 15 system malfunction
Well we have a new one today, #15 system Malfunction. Machine goes into E stop and can not clear it (control power/main disconnect off then on) like what we had last week. Any ideas as to which...
View ArticleT2 Progamming Issues
Hi all, I am helping a friend with a Mazak QT25(1985-ish?) and am stuck. Got an NMI battery alarm and got it recharged. Then an NMI parity alarm and got it reset. Now when i try to program or alter a...
View ArticleChanging a power supply on a FR SF drive
The new power supply should be here in the morning, any tips on changing it out? Looks like there are a couple of Phillips head screws on the very top that hold it in on top and three wires to...
View ArticleClik here to view.
New power supply + alarm 039
Installed the new power supply and everything powered up fine till this Alarm came up while running the spindle in MDI mode. I'm no sparky so any input will be appreciated. Attached Thumbnails
View Articleno power MAZAK QT-15n T32-2 1990
Hi I purchased a used MAZAK (1990) QT-15n T32-2. I saw the mazak running before I purchased it. The mazak sat in our shop & only connected the mazak last week When I first turned the mazak on I got...
View ArticleClik here to view.
Align turret on mazak qt30
Folks, The turret is 24/1000" off center. Off course not in the X-axis, this i could correct with the parameters. It would be the (non exist) y-axis. I tried to loosen the 8 screws and hit it with a...
View ArticleAnybody replaced a Mits VFD with anything else?
I was just wondering if anyone has replaced their FR-SE or otherwise with a plain old 1200.00 VFD (Hitachi)? Its not something I need to do at the moment...... but reading about Captdaves dilemma, and...
View Articlemazak quikturn 6t tplus controller turret isses
Im bringing this machine back to life turret was out of alignment i realigned it now im getting a alarm 398 turret controller alarm and it isnt rotating please help. I dont have a alarm list for this...
View ArticleDesperately need to add collet system to qt 10
Hello again all So like I posted earlier I got the contract on the funky parts with internal grooving see my previous post about grooving, Any way I am to the point that I would like to buy a collet...
View Article