MAZAK SLANT TURN 20 ATC NOT HOLDING DIMENSIONS x axis :(
Machine is not holding dimensions on the x axis one part comes out .185 next .183 the following .186. Tools are tightened properly. I had a similar problem with a Haas,turns out I just had to turn off...
View ArticleG18 plane change on Mazak
Hi, I am new on this forum so apologize if this subject has been raised before. Now to the point: at the end of mazak programing book are several programming examples. Among them is example 5: use of...
View ArticleVTC-20B error 209 slideway oil malfunction
We have a 1997 Mazak vtc-20B M Plus control. We are getting error 209 slideway oil malfunction. Bijur #26203 way lube system. I cleaned the way lube tank that had sludge build up. Replaced the filter....
View ArticleFR-SE SE-IO1 circuit diagram
Hi all, I know its a long shot but would anyone have the circuit diagram for an SEIO1 card? And help would be much appreciated Thanks Mick Sent from my SM-G930F using Tapatalk
View ArticleClik here to view.
Mazak Mazatrol CAM T-2 Question - MNP Process
I have generally been parting off using a manual process so I can also chamfer the back side of the part during part off. Using a 3mm groove tool. I changed this process for a part I am now working on...
View ArticleStatistics on SF-CA card problems
Hello to everyone here! This time something like a little poll. As we all know number one problem in Mazak electronics is VFD. Im interested about SF-CA board that lives in Mitsubishi FR-SF- do You...
View ArticleMazak qt15 sub Chuck problem
I have a 1989 mazak qt15 with sub Chuck. The frenic 5000 drive is giving me a error code and will not let my mazak run. I don't use the sub Chuck and am wondering if anyone can help me with finding the...
View ArticleOld QT10 Turret alignment. Need help
Hi guys, I have an old QT10 with horizontal turret and its out of alignment a little. Anybody have any suggestion on how to align this setup? The manual for the machine can be seen here: mazak t1...
View Articlekm63xmz
Hi Guys, does anybody know a good source for the km63xmz toolholders for the integrex in the uk? we are after some drill collects and 25mm shank holders. seem to be a bust at kennametal over here....
View ArticleMazak (45 E stop) After New Power Supply
I have a mazak vtc-16b with m32 controller. Last week I turned on the back controller, no issues. When I turned on the front controller, I didnt hear the valves and I wasn't able to retract the X, Y, Z...
View Article2ops in same program - Mazatrol 640T - can I offset shift
I am trying to increase throughput on our Mazak ST 80 lathes by combining two ops into the same program. (Same internal Grip for both operations) What I am trying to achieve would be easy in ISO but...
View ArticleMazak SQT 15 MSY Dual Spindle TPlus- Operation and Programming help
Our company recently purchased a used SQT MSY II with a T-plus control and dual spindle. I am familiar with the fanuc control on a 2 axis lathe but the Mazak multi axis is a whole new level. I have...
View ArticleIntegrex HSM CAM post
I have been working on a MAzak Integrex with Fusion 640mt control post for Autodesk HSM. Should also work with Fusion. Here is a link to the post in the CAM section. THis will also be very close for...
View ArticleQuestion about teaching the Z.
I run a Vortex 1060V/8, and I'm new to machining in general. However, I have a question about teaching the Z. When we setup a fixture, we set the Z off the height of the tooling ball. This is a known...
View ArticleClik here to view.
1987 Mazak Quick Turn QT8SP Loss of Parameters
Would anyone happen to have this machine or something similar? The parameters were lost. The battery was replaced with machine off by previous owner, and now a bunch of functions do not work. Functions...
View ArticleRenishaw OTS Z overtravel alarm when touching off tools with Smooth G control
I recently had to relocate the Renishaw OTS tool setter on our Mazak 530C with the Smooth G control. I relocated it, indicated the stylus, put a reference tool of known length and diameter into the...
View ArticleMazak Integrex. Mazatrol to EIA BACK to Mazatrol. Problem
Hello, Im having a issue that has us stumped. We are doing a hobbing OP in EIA format on the integrex which is working great. But we would like to do some turning in mazatrol also. In the main mazatrol...
View ArticleClik here to view.
Internal and external NPT thread program examples
After lots of searching over the past two years, I never found good NPT threading examples. But tapping and manually threading external threads got old, so I bit the bullet and figured it out. Below...
View ArticleQT8 card failures and SQT15M C-axle problems.
Ive been reading the forum and looks like there are many who are really deep in to Mazak issues. So, hoping somebody has ideas. Bought QT8 from 1994 with T32-2 lathe at this summer. Works fine, except...
View ArticleClik here to view.
Mazak Ajax Hercules 7hp 18x40 spindle reducer removal help
Picked up this lathe a few weeks ago and pulled the chuck off to find this spindle reducer I hope! I have beaten on this reducer a few times and see no movement. Used a 3ft long 1 3/4 od rod and 5lb...
View Article