Clik here to view.
YCC ER adapter
I got a few request for my YCC to ER adapters over the years so I post a thread with a drawing of them. (Old Mazak driven tools use YCC collets, with these adapters you can use standard ER collets and...
View ArticleEdit EIA File in Mazatrol Smooth G
Hello All, This is my first post on here, so hopefully you all can help me out. We have a VCN-570C with a Smooth G control and we are trying to utilize the cam software in Inventor to make the EIA...
View ArticleT32B full parameters list
I have the basic parameters list that came with my machine but thereÂ’s still a lot that isnÂ’t in there, like the machine SP parameters and T parameters so IÂ’m looking for help finding a full copy that...
View ArticleMazak SQT18 with barfeeder setup
Hello guys, i connected barfeeder to my sqt18, all works fine, at end of bar is loaded program 9999, but it hangs, i need to press cycle start to continue. Can i set to work this automaticaly?
View ArticleM32B drip feed?
Considering an old mazak mill with an M32B control, does this model come with drip feed normally? That is, the ability to run large CAM generated programs by feeding small pieces at a time?
View ArticleHTC-400 lost home positions
Hopefully someone can help, We bought a bunch of machines at an auction and ended up with a Mazak HTC-400. With Covid and all going on, the machine sat out in the warehouse for several months. Upon...
View ArticleMazak Quick Turn 100 (QT 100) - Chuck Size
Hello Everyone, I searched for awhile and couldn't find a good answer. Looking at replacing out old lathe with a new QT100 or QT200. The only reason we are looking at the 200 is because comes with a 8"...
View ArticleCFM of air required for VCN 410
Does anyone have an idea on the required CFM of air for a Mazak VCN 410 mill? I am trying to size the correct size air dryer and I cant find the cfm requirements for the machine just the psi.
View ArticleMazak Slant Turn 35N parameters
Hi, A customer of mine has just purchased an ST35N with a T3 control but unfortunately the battery was flat and parameters have been lost, does anyone have a copy of the parameters that would work on...
View ArticleIntegrex 200-IVST: Lower turrent setup and EIA gcode calls
Slowly learning to use our new-to-us Integrex and I'm stumped on how to use the lower turret on the sub-spindle. You can't use the TOOL EYE to specify tool parameters, and I don't see a way to use MDI...
View ArticleMazak Qt15 W/ T32-2 Control
Hello All, I was hoping some of you guys could lend a little help and advice on some issues that I'm having with a new to me quick turn 15 lathe circa 1989 equipped with a t32-2 control. I have re...
View ArticleQT6T Hydraulic Pump Cavitating
The hydraulic power pack on my QT6T is cavitating and losing pressure, shutting the machine down. The oil tank is full. It started a few weeks ago, with an occasionl growl that would only last a couple...
View ArticleBubble Memmory Option Parameter T-3
Does anyone know the Option parameter for the Bubble memory on a Mazatrol T-3? Thanks in advance!! Regards, Heli
View ArticleClik here to view.
Mazak VQC 20/40b loosen the hydraulic hose
Hi I have bought a Mazak. To Transport through the Workshop gate, i have unfortunetly to remove the Electrical Cabinet. As you know, many Hydraulik Hose are mounted with the Distributor block on the...
View ArticleG61.1 always on
A major problem with two of our Fanuc machines is that they lack the corresponding option and thus the resulting diameter of circular interpolation always vary depending on feed. G61.1 eliminates this...
View ArticleIs a QT8/QT10 type machine too much for a home guy?
I have been looking to upgrade my Southbend 9L since I now have a workshop. I have a small compressor, 220v RPC power and a big roll type door. I do a fair bit of aluminum and a little steel. A few...
View ArticleParameter for radius compensation on cut off
A used machine that i just purchased is not compensating for the corner radius on my cut off insert. It only goes to zero and retracts which leaves a small tit on the face of the part. Does anyone know...
View ArticleMazak Quick turn 35 N parameters needed T32-2 control
Hi i have a 1990 mazak quick turn 35 N with a T32-2 control the machine had some problems and had to reset the control which wiped the parameters somehow, but when looking for the parameter list it was...
View ArticleChanging tool in ISO/EIA program
Is there any way to call a tool using tool name, diameter and suffix, instead of tool pot number? The control is Fusion 640M. It seems Mazatrol's 3-digit G-Code does just that inside different units,...
View ArticleHow to Pattern Multiple Tool Paths around the part circumference?
Hi all, We have QT200MY and I've got a job where I could really do with some help. The tool path is a simple cut using ZY with a standard endmill, creating a v-notch on the diameter of the part running...
View Article