Misoperation 3
I am running a Matrix control on a QT250MSY. Putting M0 in to stop and clean the part before pickoff with the sub-spindle. However, on some programs when you open the door the machine generates an...
View ArticleRigid tap macro for VTC-41 1991 Yasnac MX3
Dear members, after I now successfully re implemented my tool change macro on a VTC-41 year 1991 with a Yasnac MX3 control, my boss wants me to find a rigid tapping macro and implement that. I lost all...
View ArticleQt-15 rapid jumping.
Machine is a 91 qt15, t32-2 control. This is nothing I'm doing, and no one else either. Happens about 4 times a week, damn thing jumps up to 100% rapid without me doing a damn thing. I typically run it...
View Articleintegrex i 400 S ALARM " 837 TOOL OFFSET INTERFERENCE ERROR " ???
i have a problem with this alarm " 837 TOOL OFFSET INTERFERENCE ERROR " what can it be can it be in my tool data info, offsets? how did you fix it ?
View Article640 Fusion training?
Does anybody know where I can get some training for a 640 fusion controller, specifically for EIA/ISO programming? I'm in Tampa, FL. Is there anything online? Has anyone tried ToolingU? Any help is...
View ArticleWhy can't I start in the middle of a program Mazak QT200 MY Matrix Nexus
I am pulling my hair out here...... I program in EIA, I have N #'s at every tool change. All I want to do is change a program, and be able to start it back up at a tool somewhere other than the top of...
View ArticleQT20n noise at back of spindle
I got my Hitachi spindle drive running, and now have a bad noise coming from the rear of the spindle. It seems to be right in front of the belt pulley. I can turn the spindle by hand, and it makes a...
View ArticleMazak mill alarm 206 oil chiller
We are getting alarm 206 "spindle lube malfunction" on our FH480 horz.mill. We have checked our Daikin Oilcon AKJ50Y coolant chiller and can't find what is tripping alarm. Any suggestions? Thanks
View ArticleMazak load meter question
We have a 2 year old HCN-40000II. It has the 18,000 rpm spindle. We are cutting A36 with a 2-1/2" face mill and are hitting 180% on the spindle load. It does not skip a beat. According to the torque...
View ArticleVtc-800/30
Anyone have one of these? How do you like it? I am worried about the spindle HP and rigidity. Any input would be appreciated.
View Articlerestart with a mazatrol m plus
let me start by saying i've been running mazak mills lathes and integrex for 10 years and my experience has been mainly with 640 t and newer controls. one of the vendors of the shop i work at asked me...
View ArticleST-30 ATC M/C ,T-3 controller alarm 20E-stop will not reset. HELP!!
I have a new to me mazak ST-30 ,t-3 controller. That I can not get the E-stop Alarm and 13 others alarm to reset . 20,109,110,111,112,200,201,202,204 and 205 those are the only ones it will display. I...
View Articleqnt 250 work light
I have a mazak quick turn nexus 250-II MSY. My problem is we reloaded the operating software. The machine is working fine mazak tech talked me thru the entire process over the phone ect... Now the...
View ArticleHTC-400 spindle oil air leak?
We are getting an air pressure down alarm several seconds after turning the spindle on, I think since I hear air leaking when the spindle turns on it has to do with the oil/air lubrication in there....
View ArticleNeed help
Can anyone tell me if its possible to set a timer on the work light in machine. Controller is Mazatrol 640m on Nexus 510cc machine. Thanks
View ArticleMazak Lathe, Tool Nose Radius Comp problems...`
I've got two new Mazak lathes, a Quick Turn Smart 250, and a Quick Turn Smart 350, both with "Mazatrol Smart" controls. I'm having problems getting the G41/G42 nose radius compensation to work right....
View ArticleThread clipping / parameter for fusion wanted
Hi, I'm looking for the parameter that controls the escape speed for outside threading. I used the parameter (f116) before on a matrix controlled lathe for clipping threads and would like to do the...
View ArticleQT20n turret only indexes one direction
Hello.....me again. I was testing some more programming today, and noticed that my turret will only index in the clockwise (looking at front of turret) direction. If I have a tool change that requires...
View ArticleOil skimmer for ST35n ATC MC coolant tank
Hey guys. Does anyone have a recommendation for an oil skimmer? I'm looking for something that will work dependably and be pretty reliable. I've been looking at a Mighty Mini from Abanaki. Is this a...
View ArticleQT15 Fluorescent work light
Any idea;s on where to get a replacement bulb. The standard 24" bulb sold here is about 3/8 of an inch too long to fit the fixture. Anyone have a source for metric (?) fluorescent bulbs? TIA
View Article