1988 leblond makino FNC 40
Hi all, just wanted to know if anyone knows anything about the 1988 leblond makino FNC 40 with the Fanuc 6m control. I am thinking about buying one for my garage shop. Any options on this would be...
View ArticleMazatrol Copy and Paste
I am trying to stop a very long program at a stopping point and restart at the same position the next day. To do this I normally write down my coordinates, insert a few spaces in the desired location...
View ArticleMazak 200SY (640M) B-Axis alignment
Hello people, We had an accident on our 200SY which cause the B-axis to be 0,1mm out of alignment. However, the B-axis indexes per 0,001° and if we index it a couple of degrees, we can get it perfectly...
View ArticleMazak HHCN-5000
Shop just got in 2 new HCN-5000 Mazak with Mayfran Chip conveyors, Before I start buying extra stuff I was wondering if anyone has hooked up a hose to the Mayfran coolant pump to use for cleaning. with...
View Articlerunning iso subprogram in mazatrol
Hi all, my first post after scanning these threads for info for many years, so thank you for all the help. I am trying to run an ISO sub program in a mazatrol main program. The WPC is set as normal and...
View ArticleXYZ machine zero paramaters 640m
Does anyone know the parameters to change the machine zero? We had a crash and our machine zero has shifted. I found the X & Z paramaters (I think, B259 & B264), but no Y paramater found...
View ArticleBacking Up Programs
I back up our Mazatrol & Fusion programs via the I/O function on the Mazak - using the Flash Card. Is there a way to save all programs at once, or as many as possible? Thanks in advance.
View ArticleMazak VTC-16B
I have a 1997 model vtc-16B and this issue has been around since I can remember. We use mastercam x9 to do all the programming. The issue is that under certain tool paths, such as some of the dynamic...
View ArticleMultiplex 620 Bar transfer
Hello, I have a question on a Multiplex 620 with a mazatrol 32-6 control. we're running an 86" bar through the machine and have multiple transfers we use to move the bar through. The current bars we...
View ArticleSuper Turbo X48 Tracer Cable
We have this Laser and the operators seem to be going through a bunch of expensive Tracer Cables. Testing them with an Analog Meter, they test fine from end to end and from end to ground. Could the...
View Article1981 mazak m4 memory light ?
Anyone remember what this light is for if its illuminated ? I can post a pic if that helps . Nothing in the manual about it .
View ArticleMazak QT6 Mazatrol Fusion 640T Harddisk issue BIOS issue
Hi, I've searched varius threads here and elsewhere, but couldn't find more then hints, but not a solution. I've got a QT6 in front of me and it does not realy communicate with me. Data: QT6 from...
View ArticleQuick turn 8n T32 electrical diagram
Hi, would anyone have a electrical diagram and possibly a maintance manual for a quick turn 8n with T32-2 control... Hard or soft I could get a copy off / purchase please, any help would be much...
View Articlet-2 hidden parameters lost
Does anybody have a list of the hidden parameters for a QT-15 lathe? I have a list of the rest of them. I have a mazatrol Cam T-2 with software version B6 Thank you Thomas
View ArticleMazak bar in help
I've got a job where the bore has an under cut but then tapers back on itself by. 045 thou in the z axis after the undercut... My lathe will only let me come back in the z+ direction by. 02 thou (....
View Articlet-2 parameters
Does anybody have a list of parameters for a QT-15 lathe? I have a mazatrol Cam T-2 with software version B6 Thank you Thomas
View ArticleClik here to view.
cycle start by-pass ?
I have been a bit curious what the last owner was doing with this , the cycle start button has wires going to this plug , maybe a remote lock ? Anyone see this before ? Attached Thumbnails
View ArticleCollect tool data from HCN 5000-II
Hello, Does anyone have any experience with collecting tool data directly from the C:/ from a machine? I believe MC_SDG/Toolinformation contains the information of the tools that are present in the...
View ArticleMilling gear shift sensor malfunction
Hi i have 2 machines around the 2000 year with T Plus control. Does anyone know why if I do not use the set up key to open the door I get the milling gear shift sensor malfunction? I had to guards off...
View ArticleCoolant on when door open
Hi i am looking to get the coolant to turn on while the door is open. Machine is a SQT 200MSY with T Plus control. I have a SQT 15MS around same year same control and I can have the coolant on while...
View Article