VQC 2050B died...now runs?
Hey everyone when I say thank you in advance for any help I have a 1986 mazak vqc 2050b and I was running along making my parts and all of a sudden it shuts off completely I power down power backup and...
View ArticleSurge protection
I'm going through our insurance renewal and they're asking about surge protection on our machines. Does a 1996 Mazak SQT15MS MkII have any sort of built in surge protection in case lightning or an...
View ArticleQT15 tool eye adjustment (mechanical)
Hi everyone! Have a question- how to adjust position of tool eye arm so that its stays correctly at the centre line? The problem is that arm on my machine is pecking downwards about 3-4mm out of normal...
View ArticleGetting an ST30 ATC/MC
Hey guys, So I'm getting a big mumma! An ST30 ATC/MC! It's a bit of a questionable buy (recently taken out of work and put in the yard under a tarp because then needed more room and it had a battery...
View Article1999 Mazak QT-250 issue
Hello, I came back from vacation this morning. I turned on my machine. Which I just machined parts on prior to leaving for about a week. When I fired the machine up it is giving me a Turrett Servo...
View Article1999 Mazak QT-250 issue UPDATE
Update. the alarm on the screen is a 371 Turret Servo Alarm, when I open up the electrical cabinet the MRJ drive for the turret I believe is flashing. AL-01-23-01 Also when I go on the pc side of the...
View ArticleClik here to view.
Preparing for turret hydralic seal replacement on 1989 QT8N
I have about a week of downtime between jobs on my 1989 Mazak QT8 and would like to replace the hydraulic seals on the turret shaft assembly during this time. I have a steady hydraulic fluid drip on...
View ArticleIntegrex leaking like a sieve
I just got an integrex 400Y from 2001 with a big problem. It's leaking air like crazy. My 5.5kW (7.5HP) air compressor gets properly toasty in far less then an hour when the machine is running. So far...
View ArticleClik here to view.
HCN-6000 RS232 Issue
Hello all, Used this forum for a while now, finally decided to make an account. I have setup all of our other machines for RS232 transfers, one Fusion 640MT and the rest M32s, they have been working...
View ArticleTapping weirdness on new Mazak
I recently visited the shop I retired from and the programmer that replaced me said that the new mill, when using a G84.2 tap cycle had to have a M3S500 ahead of the G84.2 to turn the spindle on or it...
View ArticleMatrix 2 pop up alarm
Hey Anyone know how to turn off 'alarm navigation' pop up windows on a matrix 2 control? Never seen them before jumping on this machine and they are annoying as hell Cheers on advance
View ArticleSQT18M Mechanical Parts List
Hi, anyone here have a SQT Machanical Parts List on pdf? It's for a T32 vintage machine.
View Article640T Reverse Cut soft key
Hi, Just having a question that i cant find an answer to. there is a softkey on my 640T control labeled Reverse Cut, and i cant find an explanation anywhere of what it actually does. Any input?
View ArticleGrooving on a T1?
Looking for some advice on grooving for my QT10 with T1 control. How should I be programming grooves that are much wider then the grooving tool? Should I do a series of grooves and set spacing to...
View ArticleATC not in starting position (Integrex 400Y)
Hi. I was running a program and wanted to pause it for a quick check and i stopped it during the arm swing but now it wont play along anymore. I have removed the tools and i can move all the tool...
View ArticleClik here to view.
mazak sqt15msy live milling need help with programming
we have a 1996 mazak sqt15 msy with a tplus control. This is our first machine with live tooling and need some help with programming this part. Can you please tell me which mazatrol process we should...
View Article1999 Mazak QT-250 chuck open / close
Hello, Can someone tell me if the chuck open / close was an option on the 1999 Mazak QT-250 with the fusion control? Also are the M-codes the same as the older machines? M6 to open and M7 to close? If...
View ArticleElectric diagram for Multiplex620 T32-6
Anyone have a PDF of the Electric diagram for Multiplex620 T32-6.
View ArticleCurses...what part number VDI clamp bolt/set screw SQT28M
For those that want to know it is Mazak Part # 43481600861 and the large set screw is # 43481600890
View ArticleQuestions about Mazak J200
We are considering a new J200 with 1 deg increments, single spindle, 36 tools. We will be looking at this machine at IMTS, possibly sooner. A couple of questions for those that have direct knowledge....
View Article