1984 Fanuc btr , Anyone know anything about this ?
I am trying to figure out if my mazak will drip feed a program with this btr or if there was special software needed to support it ? Its old I know :)
View ArticleMazak QT-15 with T2 progaming radius on end of bar
Working with a QT-15 with T2 controller and I need to machine a radius on the end/face of a bar. Can anyone tell me how to program this using this controller. Manuals are not the greatest at explaining...
View ArticleMazak QT-15 with T2 controller Alarm 13
Lathe has been working fantastic for many months. Turned it on the other day and got a code 13 and 14 drive alarms on the screen. I turned it off for 30 turned back on and no alarms. A couple days...
View ArticleV5 belleville stack
My V5 needs serious help. It will not retain tools. Therefore I need some ideas about how to go about swapping out the stack. For starters the machine is a '83; apparently a bit after Mazak switched...
View Articledifferentiating the Integrex
Im trying to understand the differences between the integrex 100/200 II III and IV. from what I understand the II have the 640MT controller and can not actively use the C axis for machining. someone...
View ArticleReform on T1, can I add an M code? Getting frustrated with this old control.
Wondering if I can add an M code to reform on my T1 control QT10? I need to run in reverse due to a boring bar being wrong hand. When I try and do a reform it does not read the M code to reverse the...
View ArticleElectric wiring diagram T32
Anyone got a PDF of wiring diagram of any T32? T32-6 GREAT :bowdown: T32-3 GOOD :D T32-2 Will do :)
View ArticleMP620 T32-6 strange X-axis problem
I dont know how to describe this problem that only seems to happen when the machine is warm (like 10 hours of work) It will change a little bit in X axis and if I dont notice it it will change more....
View ArticleEditing speed and feed on mazak quick turn 6
Is it possible for someone to explain how to edit the speed and feed on a Mazak lathe. It is a Mazak Quick Turn 6 and being a HAAS guy, I am unfamiliar with Mazak control.
View Articlemazak compact my mazatrol smooth c single process ?
when running in single process - single process stays highlighted and you have to press it again before you can run again. is there a way so that when single process has run single processs goes off...
View ArticleMazak saving program
When I edit a program on my Mazak quick turn 6, does the program automatically save in the machine directory? If not, what steps do I take to save it?
View ArticleSQT18 X-axis load
Hi, I have a new to me SQT18 (T32-3 control), I'm getting some strange intermittent noise from the x-axis when it's travelling towards the chuck, away from the chuck it's fine. Can someone please do a...
View ArticleVibrations from spindle
I cant get any fine finnish with my ST30ATC and I think its vibrations from my spindle bearings. Does anyone think I can reduce these vibrations by using a thicker oil in the spindle? :scratchchin: (I...
View ArticleSQT18m t32-3 alarm won't clear. 239 milling coupling sensor malf.
I have an old Mazak Super Quick Turn 18m with a T32-3 control. It has live tooling that i have never tried to use. I recently tried to use it and it spun a little but clearly needs maintenance. Anyways...
View Articleintegrex X axis brake
Got an integrex 400Y from 2001 with a not so good brake for the X axis. When i press the e-stop the X axis sinks slowly, anywhere from 5 to 40mm. Anyone knows if it just needs some cleaning, tensioning...
View ArticleMazatrol M32a Trouble
Hello We have a Mazak YMS-30 machining center with the following problems. - There is no signal to the screen, it is on but black. - Some alarm LEDs are registered in the numerical control module and...
View ArticleMazatrol M32a Trouble
Hello We have a Mazak YMS-30 machining center with the following problems. - There is no signal to the screen, it is on but black. - Some alarm LEDs are registered in the numerical control module and...
View ArticleInformation on a MAZAK Powercenter V7.5
Hey, I recently purchased a MAZAK Powercenter V7.5 from approximately 1984 as the first cnc machine in my shop as it came as a really good deal. Sadly it didn't come with any information/manuals. Does...
View ArticleClik here to view.
Mazatrol M32 - power supply
Someone knows the type and code of the power supply (VIN: 110vac - VOUT: +12,-12 and 5VDC) that is on the operator panel and feeds the MC221 card (NC OPERATION BOARD I/F CARD) Thanks. Attached...
View ArticleClik here to view.
Mazak Integrex 50, really (maybe) basic help
My company has a Mazak Integrex 50 w/ Mazatrol 640 FusionMT that's basically a boat anchor right now. This isn't my normal facility, but they let go of the programmer down here and called me down to...
View Article