Clik here to view.
Mazak VQC15/40 10000rpm spindle oil mist lubrication
Hello! Just got my hands on machine trying to save it. Without better knowledge I think it consumes a lot of air. Anyone has a better understanding how spindle air-oil lubrication should work. More...
View ArticleAutomatic Drill Length Compensation - MAZATROL 640M
Machine: MAZAK MAZATECH FH-6800 Control: MAZATROL 640M Does anyone know the parameters to control the automatic drill length compensation? IÂ’m guessing there would be 1 parameter to switch the...
View ArticleClik here to view.
Mazak - SQT10MS - Illegal Exception
Hello, Old granny Mazak SQT10MS About 4 months ago, the machine was having problems with the T32-3 control. It came up, just did not could not touch buttons, etc. It was unresponsive. So, based on...
View Articlemazak integrex 200s iii jaw tool stuck in spindle?
hey guys, I'm a supervisor in a machine shop that has a mazak integrex as stated, the man running the lathe went to disassemble the jaws to clean behind them since he had been running bronze, and well...
View ArticleMazak QT8 T2-Cam Wiring diagram with parameters lost
Hello Everyone I have big problem with my machine parameter lost and i would like to do reinitialization but problem is that i dont have oryginal parameters can somebody have wiring diagram from this...
View ArticleClik here to view.
Mazak - SQT10MS - EATING hydraulic oil
Hello, Mazak SQT10MS machining a bar only to come back to a red flashing light. The T32-3 control said something to the effect 'low hydraulic pressure'. So, I checked the hydraulic oil and sure enough,...
View ArticleMazak QT8 T2-Cam FX701 WDAL error LED
Hello Everyone We have problem with freezing our machine i wrote about this on other post but will be bether to make new one The problem is sometimes after couple of hours work machine somethimes when...
View Article1984 Mazak ST 40 4 axis Fanuc 6T Controls
Please help! I am trying to resurrect an old Mazak ST40 4 axis with fanuc 6t controls. I have an alarm -Z OT 221. controls still say LSK. I cannot clear it. It is for the upper turret I think. Neither...
View ArticleNeed a sample 640t SQT100mst bar program, EIA, sub spindle sync?
Hello, Just doing a simple bar program with a SQT100MSY, 640t. Turn the end sub spindle clamp & sync. reposition repeat We know how to part off and end work, we use a 9001 sub-program for that....
View ArticleMazak remote (offsite/over internet) control
So I have a number of older mills and one lathe (2 with M plus controls, a M2 control, a M32 control, a M32B control, and a T2 control) and have this crazy idea of remotely controlling them. I have a...
View Article1997 Mazak VTC 16A
Hello, I just moved my machine shop to a new location. Once we were ready to fire up the Mazak Mill we are getting an alarm while trying to home out the machine. "Z" and "Y" will both home out. I am...
View ArticleMazak VQC 20/50A delay between units
So I have a VQC 20/50a that runs pretty decent but have noticed that it moves quickly within a unit or when going to a new unit with a different tool but when you have the same tool prioritized to be...
View ArticleCharging backup batteries
I have a T2 machine with 2 backup batteries. The machine will end up being unpowered for a few months and I'm wondering if I can charge the backup batteries directly while they are still on the board....
View ArticleMazak Matrix2 i630v Integrex - Macro Variable List
I am searching for a EIA Macro Variable Listing, in general, for Mazak / Matrix2 / Integrex / i630v. (Future Usage) Specifically, the variable for the pre-call tool number in the standby pocket. I know...
View ArticleFR-SE - Over Voltage (Converter) Error
Hi Brains trust. trying to resolve an intermittent error with the FR-SE-2 spindle drive. The drive is tripping out on over Voltage (Converter) somewhat randomly. A week or so ago, I was in the middle...
View ArticleClik here to view.
QT10 turret end cap removal
Simple question are there any surprises to removing the end cover on a QT10 turret I'm replacing the way cover wipers and such problem is the PO ran a bunch of stainless with the chips caught between...
View ArticleSQT200MS Air Leak
Hi, I've just been to look at a SQT200MS 1998 T+ lathe that's being sold at auction. Whilst inspecting the machine there was a loud air leak coming from the main spindle area, not knowing this machine...
View ArticleUsing tool eye for broken tool detection, Integrex 200IISY
Hello all, I'm trying to use the tool eye for broken tool detection and don't know how to go about it. All I know is G36 is used but that's all. Is checking for a broken tool with the tool eye...
View ArticleRelief Groove
QT10-N, T-Plus Control I have a 1 1/2 x 8 internal thread. I've been using a boring bar (93 / 35) to put the relief groove on the inside. It's working fine but the problem I'm having is it's packing up...
View ArticleMazak qt-6 1997 turret info/problem
I was helping out a friend on his qt-6 with a tplus control. There was a ecsessive internal hydraulic leak in turret lock cylinder. Removed lock cylinder and replaced all O-rings. When putting turret...
View Article