QT15, parameter list
Hi, could you help me, looking for parameter list for QT15, Yom 1989, Mazatrol CAM T2. We bought it in Spain, have not any docs with machine..
View ArticleMazak QT15 CAM-T2 Error 13 Drive Alarm X Axis
I am getting this alarm ( Error 13- Drive Alarm X Axis) and trying to figure out a few things. The error initially occurred and can be consistently repeated during a drilling cycle. Drilling a 1/2"...
View ArticleM-code for X-axis home?
Hey, When turn threading we remove the start/end of the thread by milling using manual program. Program looks like this (for external thread using endmill at B90(non freedom units)): HTML Code: G1Â G2...
View ArticleIs there a way pattern a program in Mazatrol (M32 or M+)
Basically I have a program for one part but am now going to be make a 42 parts at once out of a large sheet. Is there a way that I can just pattern the same program across the sheet? Thanks,
View ArticleMazak AJV-18N spindle drive down
So my AJV-18N went down 2 days ago. I determined that the issue was with the spindle drive. After getting a troubleshooting guide from Mitsubishi, I determined that they issue with that spindle drive...
View ArticleClik here to view.
Mazak vqc 15 servo lag excess.
Hello. My old mazak started throwing this error when I changes tool. It doesn't do it every time. Anyone know what cause it ? I can restart the control and go again but it's getting annoying and I want...
View Article2 z axis servo lag
I have a Mazak QT20N from time to time it alarms out with alarm #2 Z axis servo lag any ideas on this . Thanks
View ArticleQT15 Phase Converter Requirements
Hey everyone, I know this is a bit of a contentious subject but having searched a bit it seems there are different opinions floating around about what the true phase converter sizing requirements are...
View Articleask for the operation manual of Mazak's Vertical Machining Center
Hi everybody, I want to learn the operation of Mazak's Vertical Machining Center,but i have not any book or manual ,Could you tell me where i can find these book? Thank u.
View ArticleClik here to view.
Raise max spindle rpm
My Multiplex 620 T32-6 as a max rpm of 3600 on the spindles. I found a label on the machine says max 4800 rpm and the chuck says max 5000 rpm. I tried to change parameters to do 4800 rpm and it works....
View ArticleDoes anybody have a copy of Mazatrol T32-B programming manual please
Hi I have just purchased a Hyundai Quick turn 15N which i beleive is just a rebadged Mazak qt15 It has the Mazatrol T32B control and i am wondering if anybody has access to the programming manual for...
View ArticleMazatrol t-2 stupid lathe question.
We don't use this lathe too often and I am not too familiar with it. I programmed a part using both a left and right hand tool. There is about a .075" difference (part has a perfect .075" thick disk...
View ArticleNew (to me) machine day! Error 28 t32-6
Hey guys. Just got my new (to me) multiplex 630 (t32-6) delivered today. Hooked the bad boy up to power and air and the pump got up to pressure, so I got phasing right on the first go, so that's a win....
View ArticleFinish Stock
SQT-10, T-Plus I assume on the first line where you define your X finish stock, that is for both ID and OD. My question is what If I have a bore that I want to leave less stock because of tool size....
View ArticleT32-6 MP630 wiring diagram?
has anyone got a T32-6 Multiplex 630 wiring diagram? or any t32 or multiplex wiring diagram? cheers, Trav
View ArticleQuick turn 15 will not zero out / home on start up
Hi all My machine is actually a HYUNDAI badged quick turn 15N with a T32B-b mazatrol controller I bought the machine in an auction and could not view it or speak to previous owners or operators The...
View ArticleAdding EIA to T32?
Hey kids, Has anyone successfully added EIA to a T32 controlled machine? We've done it on T2/3 machines through the power of the hive-mind that is this forum, surely we can achieve it on the T32?...
View ArticleEverything Stopped
SQT-10M T-Plus. I powered up the machine. Set a tool with the tooleye. Was running the spindle at about 500 rpm to let it warm up a bit. Pulled up the program and standing there looking at it and then...
View ArticleMazak ATC Alarm 212 & 300
Operator hit the reset button in the middle of a tool change on our Mazak Horizontal Center Nexus. The drum is now cocked at an angle with the next tool that was ready to load. We haven't been able to...
View ArticleDisabling tool setter on vqc 40/15 M32 control
I got some switch fault in the toolsetter and I never use it. Anyone know how to disable it ? I can't find anything in the manuals Sendt fra min EML-L29 med Tapatalk
View Article