Mazatrol Matrix Nexus program directory
I have a Mazak VCN 700D-II with the Mazatrol Matrix Nexus control, and we have over 1000 programs in both the standard and backup program directories. would there be a way to create other program...
View Articlemazak matrix machine menu name display
After a hard drive replacement the names for the coolant and machine menu keys are missing, the keys still work just the names on the display are missing. I have access to the old hard drive files on a...
View ArticleClik here to view.
How can I get rid of this message?
Every time when I try to change parameters I get this message. Any solution for this? Attached Thumbnails
View ArticleMAZAK Integrex - tool trace point recalculation problem
Hello everyone. I am working with MAZAK Integrex machnines and sometimes i need to machine some parts with a turning tool, using different B-angle. We are using eia program format for our machines....
View ArticleT-32 emergency stop. Can't find the cause.
Hi. I'm stumped. Machine is an old quickturn 28N. I've owned it for about 15 years.It's like my best friend. We've had our ups and downs. All the drives have been changed over the years. Power supplies...
View Article284 Unclamp error Mazak VTC16C with M32B
Hi all, I have a Mazak VTC16C with M32B control. I am trying to manually unclamp the tool but I get an error '284 Unclamp imp.(spindle ori.unfi)' when I turn the key to unclamp I have orientated the...
View ArticlePowermaster tailstock
I have a 99 powermaster and never had to switch out the center in the tailstock until now. I can not figure out where or how on earth to remove the live center in it. Any help would be greatly...
View ArticleNeed help programming, is it possible, conversational, vcn530c
Hey guys, I'm decent with conversational on lathes. I've programmed by hand my entire career both g code and conversational. We recently acquired a mill, vcn530c, and I'm learning the programming...
View ArticleMazak 655-80 z offset help
Hello i have a mazak 655-80. Im having trouble running multi tool programs. I touch all my tools to my z setter then my boss to the part. When running the program the machine reads the first height...
View ArticleDoes MazView Work On The New SmoothG Control
We just replaced our oldest SQT T+ for the new 200MY SmoothG. Very nice machine. I use MazView on T+ and works great after making my own wire but I have no clue if it's even compatible with the new...
View ArticleRigid Tapping
Has anyone done rigid tapping in manual programming, using maztrol? have quick turn 8 T2 control.
View ArticleHow to make SS chuck to unclamp
So I wrote up a program and its all working except for one part. The program does some turning on the main spindle then the sub comes in syncs and grabs the bar and pulls it out then it gets parted...
View ArticleClik here to view.
2008 Mazak QTN 200-ll missing entire tool eye arm...one from another model fit ?
Some used tool eye assemblies on eBay from scrapped machines....wondering if any of them might be "close enough" length and position wise to work. (add in the iffiness of the wiring and plugs being...
View ArticleClik here to view.
Mazak Nexus 200-II M problem
Hello and good day. I have a problem with one of our Mazak Nexus 200-II M. I have the following problem: When i boot the machine on the NC side i have the error OC . After i reboot the machine 4-5...
View ArticleCan anyone here look and see how their tool eye is wired to the electrical box ?
Bought a used tool eye where they cut the wire cables.... that aspect is no particular problem as I can pretty well guess what wire does what (plus one air line)...but very curious where the wires end...
View ArticleMazak V5 will not retain tools
I have an elderly V5 where the Belleville stack is broken/weak and needs swapping out. Machine is one of the first where the spindle comes out the top. (1983) I need docs/guidance on how to change out...
View Articlemazak v515/40 electrical issues???
Hello everyone thanks for letting me join this is my first time joining any forum at all but i have been reading posts on this forum for quite some time and have helped me quite a bit over the years so...
View ArticleMazak Nexus 510c - Y axis noise
Hi guys, new to the site and also new to Mazak!! Wondering if anyone could offer any suggestions for a problem we have with a Nexus 510c (Heidenhain iTNC530)? The Y axis will make a whining/groaning...
View ArticleMAZAK QT15 with T2 cam cnc controller
hey! can anyone could help me with the parameters, manuals of this machine. It will be great help .I am using QT15 with T2 controller . Thanks. Ping me on my email: yashikapatil18@icloud.com
View ArticleM Plus hidden/privilege parameter
Does anyone have a list of descriptions of the hidden/privilege paramaters for a M plus control? I can get to the hidden parameters but my documentation for the machine does not list them therefore I...
View Article