Mazak Lathe Chip Conveyor Control?
Hey Guys, I for the life of me can't find the menu that allows the control of the chip conveyor on my lathe. I know it exists, as I have done it in the past. Somewhere there is a menu that allows you...
View Articleerror 1276 SlantTurn Nexus 550M
Hello all I was hoping someone could help with a problem with one of our Mazak SlantTurn Nexus 550M's We have an error 1276 tailstock sensor malfunction. We wonder if someone can inform us how/where to...
View ArticleQT15n coolant pump setup
My 1990 QT15n has 2 coolant pumps. One that feeds the turret, it works fine. And a 2nd pump that apparently is just chip wash through a distributor pipe. This second pump works fine, it thoroughly...
View ArticleSpherical Radius Face of Part Quick Turn 250 Fusion
Nobody at my shop can explain to me how to program spherical radii in fusion. The people up front responsible for drawings rarely give me enough information on the BP to even try to figure it out...
View ArticleClik here to view.
Brand New QT250MY Smooth Programming Issue
So my shop recently just got a brand new QT250MY. We're a mazatrol shop, I'm mostly familiar with an older SQT with a T+ controller and my coworker runs an integrex with the matrix. We were setting up...
View ArticleClik here to view.
510C Nexus, closed start and end causing tool interference alarm.
I really don't know much about programming Mazatrol. It's a 510C mill, with the Nexus controller. I'm trying to cut some jaws. Unit 4 used to be a Slot unit, but I changed that for a Line Center. But...
View ArticleSQT 250MS sub spindle jittering.
Ran last Friday for about 6 hours straight and threw an overload alarm. Sub spindle rotation was a bit stiffer than normal, and chuck very warm. Motor was very hot. Let it sit all weekend and all...
View ArticlePre Made Macro Programs for MAZAK or FANUC for download
reduce downtime start cutting metal chips Pre-made macro programs for download, ready and easy to use just fill in the blanks, quick and easy. Click the link:...
View ArticleMazak MTV815/120 X-axis error.
Due to the fact one of my operators did not tell me the back up battery has failed and I lost everything I did a parameter restore off the disk that was in the machine and now my X-axis is reading...
View ArticleClik here to view.
Mazak SQT 18 MS subspindle stuck
Has been sitting in shipping container for 1 year in FL. Greased everything in interior with PB blaster surface shield spray. Went to check on it since last 3 months and now subspindle ain't rotating....
View ArticleClik here to view.
Matrix Nexus - Bar Face with Edge Tool?
Hello. I've been struggling to find the proper way to program this tool. It's an external DCMT holder, held in the axial direction, similar to a boring bar. I assumed that EDGE is the correct way to...
View ArticleMeldas sqt28 mazatrol t32-3
Hi, I'm having a lot of issues after replacing some bearings, I thik it might be a change in the parameters of the machine, does any one have the MELDAS parameters for a SQT -28 with mazatrol T32-3....
View ArticleSling lengths for moving mazak QT 30, 28, 25, 20 etc... are they equal?
We are moving shops and I have 6 machines to move. We're loading them with a fork lift on this end and unloading with an overhead crane on the other. My question is are all 3 slings equal in length? Or...
View Articlemazak sqt10ms capabilities
I have a project that I have to cut an octagon on the end of 1/2 round brass stock. Is the sqt10ms capable of doing this? Thanks Tim Meyer
View ArticleClik here to view.
Clone HDD Mazak Fusion 640T
Hello I try to clone the original HDD and I don't succeed I tried several time to clone the HDD with EaseUs and AOMEI software but with no luck, I am using and IDE 44 pin - Sata adaptor for an old...
View ArticleFusion 640 Integrex Polar Coordinate Interpolation Issues
Hey guys, long-time reader, first-time poster here. I bought a 2001 Mazak Integrex 100-IISY, and I'm now ready to get it running but cannot seem to get around a huge issue with the G12.1 - polar...
View ArticleClik here to view.
Matrix Nexus - How to Program a Multifeed Bar feeder?
Hello. We have a Multifeed MX-1B with our QT Nexus 250-II MS. I've managed to manually move the pushrod, cross slide, etc. The bar feeder itself seems fine. The thing is when I call the bar feeder with...
View ArticleT plus control programming radial grease groove in OD.
Looking for some help programming a radial grease groove. I think i have most of the bugs worked out but now i am getting a 638 Illegal designated tool width alarm. I am using a .078 wide grooving tool...
View ArticleMplus Control trying to use EIA/ISO diameter offsets with Mazatrol tool...
So I have a Mplus control that I have been using the Tool Data for both my diameters and length offsets reliably in EIA/ISO mode. However, because of the limitations of Tool Data, I'm unable to use...
View Article