Multiplex 620 with bar feeder SMW 2000
I do not have the Manual with the M codes for the multiplex 620 T32-6. I Am trying to make the program to work with the bar feeder SMW-2000 . Anyone could post a program as example to see how it works?...
View Articleincreasing bore of drawtube?
Just wondering if it is possible/plausable or if i'm barking up the wrong tree. When I bought my QT10n I was given the option to buy a collet chuck with it (at too high of cost for me to justify with...
View Articlei think i should just sell them for parts ?
I just bought 4 used Mazak qt 20 1995 models . they are in ruff shape but where running in production. I don't think they were ever cleaned from the time they were installed new. Maintenance on them...
View ArticleDrawbar problems
Hey guys I'm back again I have had nothing but problems with my sqt18ms .... The chuck now closes on a part and doesn't hold pressure but my hydraulic pressure stays up .... There is a slight little...
View ArticleHow to restart in EIA mode?
I cant seem to figure out how to restart a finish pass in EIA mode. I have the manual's but I can't understand any of it!! I don't want to have to run the whole program again just to get to the finish...
View ArticleIntegrex J300--saving programs to USB
Can someone out there shed some light on how to save a program to a USB on an Integrex J300. (Matrix control) We have had the machine for 2 years and up until today, have not had a need to save a...
View Articlehow to protect 9000-series programs on an M-32
Hello - An operator deleted a bunch of probe programs from an M-32 control (Mazak H800 Horizontal Machining Center) to make room in order to get another part program loaded. These are 9000-series...
View ArticleHow large is a typical EIA program, byte size?
I recently needed to machine a small area with my 530C Smart vmc, about 3" diameter area with a contour bottom, and tapered side. A friend modeled and posted an EIA program from MasterCam for me. Size...
View ArticleIntegrex C axis Home posistion
The machine is an Integerx IV with Matrix control. When the main spindle is at C0. the home light is not on. When commanded to G28H0. the home light comes on but the position displayed is 90.1563. So...
View ArticleMazak QT-15-SP Power requrements
Hello All, Have a question as I am moving shops and there is different voltages at the old shop vs new. I currently have the machine hooked up to 480 and everything running, I am moving to a building...
View ArticleTurret Battery Died Need Help Restoring Position
Quickturn 100M battery died for the turret. Replaced all is good but now the turret shows no tool. I tried following the process in the mazak book but still show no tool. I tried three or four times....
View ArticleEngraving part numbers on face of part with C axis T+ control
Need a little advise on this subject please. Have a hand full of part numbers to engrave on the face of a family of parts but the CAD/CAM package I have is mill only. Is there some free ware or...
View ArticleMazak QT20 Universal T1, Removing pneumatic chuck and replacing with a scroll...
Hi Guys I have a Mazak QT20 Universal with a T1 controller The old self contained pneumatic chuck was badly worn, so I took it off and replaced it with a new 3 jaw scroll chuck I have plugged the air...
View ArticleCoolant Auto on
Does anyone know what the parameter is to keep the coolant auto on all the time on a mazak lathe with fusion controller?
View ArticleMazatrol T2 drilling??
So I can easily set the drill program for a straight punch no pecking. my problem is upon completion of drilling the drill will return back to Z of 0.100 or reference point at the same feed it drilled...
View Articlequick turn 15 problems
Hi I bought a qt 15 I'm trying to set it up but can't figure out how the chip conveyor fits in with the coolant tub in. If anyone would, would you take some pics of how yours is set up? Also where does...
View Article"86 QT10N question of setting 1st tool.
We just got a QT10N into the shop. There were no tools in the turret and we are not trusting the number for Z home. What is the best method for reestablishing a known tool in the turret to set the...
View ArticleT2 parameter question
I have a qt 10 with a T2 control, I am trying to change my tool approach when I run a part, currently when the turret approaches the work piece it comes in at a diagonal approach(both x and z move at...
View Articleiso parts catcher and bar feed for 88 qt15
I'm looking for a parts catcher and a bar feed for a quick turn 15 if you have anything or any suggestions of where a guy might find one thanks!
View ArticleT2 setting up a stopper?
Hey guys, How would i go about programing the turrent to end at a curtain point on a curtain tool so that i can pull out more material to a specified length? (if that makes sense at all...) Cheers, Trav
View Article