Mazak vtc owners
Hi, I have a VTC-30 we have had since new 1998. One day it did a tool change without putting the tool it had in the spindle away! Wow broke 4 fingers and damaged my virgin table and ruined two end...
View ArticleMultiple parts from a short bar using shift on T plus
Need to run a couple hundred parts from 6061 2.5" tube 1" long. Very simple part, just a clean up on the OD and ID and part off to length but our SQT15 only has a 2" bore. Plan is to saw into maybe a...
View ArticleExceeding qt 15 diameter capacity: How to do it?
I've got to quote an aluminum clutch housing that is 16" od, 5" id, and 4" thick. Mostly hollow inside, like a big flat bottomed bowl. Was a casting they don't have anymore. Has anyone cheated the max...
View ArticleCAM T-2 tool setting - auto set?
hey peoples, Maybe a stupid question, but WTF does the "auto set" button in tool set do? I've tried to use it and it did nothing. I was thinking that it might just bring tools close the their last...
View ArticleClik here to view.
Illegal cutting point?
I don't get it, what's wrong with the cutting point at PNO2? CPT-Z is 0 btw... can't see it in the pic
View ArticleSqt18ms problems
So I finally got my machine up and running .... And I left it the night after getting it going and came back the next day that the turret was lower than when I left .... I've now come to realize that...
View ArticleMazak VCN 510-C motor encoder question
Greetings. We are facing an issue with the spindle motor (Mitsubishi). We have changed the bearings as we got an alarm for spindle malfunction, and as a result there is an error on the encoder. When we...
View ArticleMazak Layout Unable alarm 851
Hi there, I have a Mazak Multiplex 620 with Mazatrol T32-6. I have a problem when I try to make a program in Mazatrol With transfer the part from head 1 to head 2, I Am getting Alarm 437, 651 or...
View ArticleMazak Integrex 35 ATC arm slide motor
Looking for a good ATC arm slide motor for a Mazak Integrex. The part number is R13QD002442. Anyone?
View ArticleClik here to view.
T32-6 with program alarm 651
I have this program and I Am getting layout unable 651 or 851. Same problem as the thread mazak layout unable alarm 851. I just created this in order to be able to post the complete program picture and...
View ArticleBlind hole broaching on Mazak NT 350 lathe
Hello all, I am pretty new to the forum and I have found some very useful information on here so I hope someone out there can help! I am going to have to set up a 3/16" broaching tool in my Mazak NT...
View ArticleMazak with M32 control VMC won't read height offset in EIA NEED HELP
I am working on a MAZAK MTV 414/22 with a M32b control. Batteries went deat. Loaded the parameters from EPROM, Changed F93,ect all four the page says reading the bits from right to left with the...
View ArticleMazak with M32 control VMC won't read height offset in EIA NEED HELP
I am working on a MAZAK MTV 414/22 with a M32b control. Batteries went deat. Loaded the parameters from EPROM, Changed F93,ect all four the page says reading the bits from right to left with the...
View ArticleSpeed and feed assistance for mazatrol vtc mill
Hi everyone I'm a noobie at mazatrol basically been teaching myself since the training at my place of employment is none existent basically I have a pretty good foundation on speeds and feeds for face...
View ArticleHow to reset LINKED MODE in Mzatrol T32-6
Hi there. I have a multiplex 620 with Mazatrol T32-6 and is happening to me that when I Am preparaing a complex program with transfers and sincronized movements; if for some reason I have to stop the...
View ArticleNeed variable for M2 part counter.
OK, I finally have need to post a question. Mostly I just read thru the postings. I have a Mazak VQC 2040 and I am running EIA G code on it. Does anyone know how to activate the parts counter? I also...
View ArticleClik here to view.
Setup problem for Multiplex 620
Hi there, I Am new with the Multiplex and also for the programming. I am trying to run a program with transfer of piece between head and head 2. I have problem with the Setup. In the book say to...
View ArticleQT8 x axis wil not cut. Need help
I am having a problem this morning getting a part to run. I have a bar stop at the beginning of the program, that will process just fine. When the next (and I have tried three of the four tools) tool...
View Article'84 QT20, T1 powering itself off randomly.
Sunday I was indicating some crappy part in on the lathe, and it just powered off... The turret dropped and squished my indicator... Powered it back on, and it powered off, then again, then again......
View ArticleSpindle Alarm Mazak Micro Mill V5
Hello, I have a 1984 Mazak V5 24 ATC with Fanuc 6M control Machine has been a work horse for my shop for over a year. However recently I've been getting a red light display under spindle and machine...
View Article