qt-15 power requirements
i just wired up a qt-15 211 volts 3 phase and no lights of any kind show in the electrical cabinet nor does the unit turn on i have looked for any diagram for the transformer but have no clue how to...
View ArticleClik here to view.
New Machine Day!
Just got our latest turn/mill center. Mazak Bartac. 5 axis, 72 tools. 8 inch 5 jaw main spindle chuck with a 4 inch through hole. 6 inch subspindle. Barfeeder and part unloader, tool probe, many other...
View ArticleClik here to view.
Parts counting on a PFH-4800 w/640M
got a quick question that I'm hoping has a simple answer. On the Mazak we run the fixture holds 4 parts that are machined in succession. I have found the line at the end of the program that turns on...
View ArticleClik here to view.
SQT15MS-T-Plus Bar Pulling Program
Hey All, A bit of a rush order for 500 brass screws has me scrambling to figure out how to bar pull with the turret. Does this look about right? I'm going to load 4' pieces of ⅝ brass, then just let it...
View ArticleMazatrol Question - Manual Process, T-2 Control
I am using a manual process for parting off to control spindle speed during part-off (which I learned here in another post) and I am using the parted off edge as a finished face since finish is good...
View ArticleI'm ready to give up
Well after all the other problems I had with the VQC20/50b I had it running properly for a little while. Yesterday I wrote a simple program and when I went to run it it picked the required tool then...
View ArticleMazak INT 40 ATC M/C
Hi everbody, I am pretty new in this forum.I have a Mazak INT40 atc m/c. We lost all datas resident in directory .01 Now I can not change tool. because of missing macros. I would be grateful if you...
View ArticleClik here to view.
New machine day
Got a new machine just before christmas: Mazak Quick Turn Smart 200M. Options: Chip conveyor, 5bar cooling, 2MB memory and ready for bar feeder.
View ArticleTailstock Programming?? (mazak T-2 control)
I am making some little parts that get parted off. Currently they drop onto the chip conveyor but I had one this week take a bad bounce or get stuck in some chips or something and get stuck between the...
View ArticleSpindle orient on a QT10 T-2
I am trying to do a internal hexagon with a tool that require the spindle to orient 60' 6 times. The machine does not have a C-axis but it has the spindle orient function, but can this function be used...
View Articlem32 operators manual
anyone have a copy of operators manual for m32 control or know were I can find one ?
View ArticleMazak or Mori
Looking for input 1000mm horizontal. The company is looking at both and ready to pull the trigger. Eventually these machines will have a large pallet pool and be fully automated. Sounds like fun huh?
View ArticleDual spindle work holding in mazatrol
I'm OD turning a 5.5" od x 18" tube and need to hold it with both spindles. Mazatrol programs won't start with the subspindle out of home (that I can figure out), and I'm trying to avoid using a...
View ArticleClik here to view.
Grooving - Bar Out Style - Mazak QT10 w/ T2 Control - Retract Issue
Hello everybody, I'm having what I'm sure is a common problem, but I can't figure out the solution for the life of me. I've programmed a mold mandrel on our QT15 using Mazatrol on a T-2 control. The...
View ArticleClik here to view.
Sub-spindle ONLY machining.
Hey All. Yet another thread from me. I'm trying to machine a piece of stock in the sub spindle to use as a centre. This is what the program looks like so far. The programming book doesn't have much on...
View ArticleQTN 350 MSY sub transfer problem
having problem with main chuck not opening on a transfer from main to sub, I"m machining part on main, pull with sub both c axis at 0 not spinning using 2 bar transfers, drill a line of holes, this...
View ArticleST30ATC M/C T3 hidden parameters.
To make a long story short: I have a ST30ATC M/C T3 (32 tool storage) and need the hidden parameters, or a description of these. I only have the other parameters.
View ArticleHelp with 128 alarm
I have began using the probe in my 510C II and 530 to set offsets and when I put the probe away and call a tool to touch off the Z I get a 128 alarm. Interaxis override. How do I overcome this?...
View ArticleMazak QT-15 Spindle Alignment Question
Well I went and ran the turret into the chuck. Chuck was not running so that is good. I was testing something out and entered a quick little program to try it and forgot to set the z offset so it used...
View ArticleV655 Z-axis drive issue
Hello everyone, I'm having a pretty big issue with my V655 and its left me scratching my head. Sometimes the machine will throw itself into an external estop and it sites the Z axis. When it does...
View Article