Clik here to view.
Anyone have a angle live tool holder for my QT10ATC for sale?
Anyone have a angle live tool holder (VDI 40) for my QT10ATC for sale, I have 5 and need 6 for a setup. These was standard in the smaller machines in late 80 and early 90.
View ArticleNeed help! Mazak VQC 15/40 M-2 control Locks up at tool change
I have recently bought this machine Mazak VQC 15/40. Finally got It running this week. When it goes to change tools it moves to change position. Then moves very small amount and locks up. I have to...
View ArticleMazak SQT10MS - Box Way / Gibb Adjustment
Hello Friends, 94/95 Mazak SQT10MS In setting up a job, and drilling in the rear spindle, I visible noticed some 'play' in the entire spindle assembly in the rear. What I mean is that when the drill...
View ArticleMazak QT8 test more help
Im still messing with trying to bring my Mazak QT8 back to life It keeps getting closer and closer but still not able to make a part. Im trying to push my "TEST" soft key on my mazatrol cam T2 and it...
View ArticleMazak QT8 No MSR
Hello out there, new Mazak guy here. Been running two Mazak Lathes a QT25 and a QT8 for the last year now. Recently the QT8 went Brain dead, had to have a replacement board, the works. Now it has no...
View ArticleClik here to view.
Program help needed
Hello guys. Need help with another feature maybe one of you guys wouldn't mind helping out or even sending me a photo of what the code should look like. Attached are drawings I hope are sufficient. The...
View ArticleQT-8 bar feeding questions
We haven't seen much use out of this machine in the last 6 months and was thinking of selling but of course a new long term project (for our in house products) just made itself available ~ 30,000 per...
View ArticleMazak QSH-10 Lathe T-4 controller
Looking to see if anyone may have a T-4 programming manual/ operational manual? Info about this lathe? Very limited info about the lathe in general.
View ArticleHow to slow Spindle ramp on T1 Controller??
Hi Guys, Im working on an old QT10 with T1 control and Im trying to slow spindle ramp time. Machine is running on a phase converter and im getting an alarm when starting and stopping spindle at high...
View ArticleQt15n t32-2 controller
Hey guys, I need your help, I'm chasing a repair manual for my old mazak, t32-2 controller, started the machine up shows e-stop alarm, tried to boot it several times, same fault. If anyone has a repair...
View ArticleClik here to view.
Help identify this collet chuck
Picked this up several years ago and been in storage in the basement but no manufacturers name or part number anywhere on the chuck itself. It just happens to have a 5/8" collet pads installed, just...
View ArticleMazak QT-20 manuals
Hi all I´m new to the forum, seems like there´s a whole lot of good info here! I´m close to buying a 1997 QT-20 with T-plus but the manuals are all in German according to the seller, I´m from Sweden...
View ArticleT-Plus- Any way to set different finish allowance for OD and ID?
I'm turning some 4340 HT that wont break a chip worth a shit on the ID at .040" doc. Is there an easy way to set a different ID and OD finish allowance without programming roughing only, and going...
View ArticleClik here to view.
Parting off SFM issues with machine or program?
So just got this machine back into service and running a simple production job and running into a snag when parting off. No matter what SFM I program during part off, the spindle will not exceed 735...
View ArticleSQT15MS Torque curve?
I was turning some 4.75" 4340HT today at .140DOC and .016"/rev with a CNMV 432 at 700SFM (560RPM), about 70% spindle load. All was fine for 15 parts, inserts lasted about 6 parts per edge. Then I...
View ArticleQT6T ID hole diameter?
I am looking at a Mazak QT6T and am having trouble finding the ID holder diameter. Also was wondering what type of chuck fits on this. My QT8 has a A2-5 on the chuck. It is calling a 4.53" flat spindle...
View ArticleProgramming error
Ok so im having and odd occurance. I'm running a part that's been modified to add a hole in the center on a lathed part. The program ran fine until I added the drilling cycle, it keeps saying out of...
View ArticleClik here to view.
M2 control for vqc 2050b reinitialize procedure need help no tool data page
So after a couple of months of waiting I finally got this machine in a place where I have a powered up and everything's all ready to go the first time I turn it on everything is great except for the 22...
View ArticleClik here to view.
What to do with an old mill?
I bought a 1989 V10 mill (M32) about 5 years ago on Craigslist. It's been a great machine but currently has a cooked x axis drive. We're told that a drive repair may fix the issue or flush out another...
View ArticleProgramming multiple radii in maztrol
Ok guys....I am a total newby to forums and I need help to write a program in maztrol. It is a 12" hollow spindle mazak. I am very familiar with the programming to a point. We do OD ID threading...
View Article