Hows does block delete work on a Mazatrol Matrix Nexus 2?
Hi folks. I know how to use block delete in a Fanuc based system, and can make mine work in EIA mode. When I select "block delete" on the soft keys, I get a new page listing block delete 1, block...
View ArticleClik here to view.
Program help needed
Hello guys. Need help with another feature maybe one of you guys wouldn't mind helping out or even sending me a photo of what the code should look like. Attached are drawings I hope are sufficient. The...
View ArticleClik here to view.
Programming multiple radii in maztrol
Ok guys....I am a total newby to forums and I need help to write a program in maztrol. It is a 12" hollow spindle mazak. I am very familiar with the programming to a point. We do OD ID threading...
View ArticleMAZAK YMS H25Q Spindle tool holder problems
I know it's a longshot because of how old the machine is but about 20 minutes ago the spindle tool holder on my machine, let go of the tool in a cut. The tool is alright and the part is fine. The...
View ArticleClik here to view.
Need help wit a QT-8
Hi Everyone, I got this machine a couple of months ago and have been slowly getting it back together. It was missing parts. Some visible and some not so visible. Anyway I finally got it under power and...
View ArticleLooking for info on the chip conveyor VTC250D/50 with a Mazatrol Matrix Nexus 2
Hi folks. Is there a way to allow the chip conveyor to run with the doors open without bypassing the interlocks? Like a parameter somewhere? Thank you! Mark
View ArticleNeed help with NPT internal single pointing w/QT-15 / Mazatrol T-2
Hi Guys, A bunch of my lathe parts have female NPT threads. Being new to this CNC lathe thing, the internal threading has scared me. Tales of Mazatrol bugs that break things. And just not being sure of...
View ArticleClik here to view.
Mazak QT18 Mazatrol Option
I have a new to me Mazak QT 18. Does anyone know where this goes or what it does? Does this mean it has the EIA/ISO option? Where would it plug in? Attached Thumbnails Â
View ArticleLowest chuck pressure setting on QTN-100
Kitagawa B-206 chuck. I run a lot of parts that require light chucking pressures and I was wondering how light I can go with the chuck pressure before I run into actuation issues. I'm currently doing...
View ArticleHELP! Need a collet chuck number 3740120130
Hey Fellas. I've run into my first big problem with my old outdated dinosaur of a mill. The Spindle let go of the tool the other day during a cut. Didn't actually hurt anything but I can see a couple...
View ArticleNeed help putting renishaw probe on fusion 640 control
I installed a renishaw MP700 and OMI on my 2002 vtc-200 with fusion 640M. I used the electrical schematic to figure out how to wire it up. The probe turns on but the skip signal does not work in the...
View ArticleMazak Nexus 510C 209 Slideway Oil Malfunction Alarm
We ran the grease reservoir empty on our Mazak Nexus 510C. Since then we have not been bale to clear a 209 Slideway Oil Malfunction alarm. I believe that there is air in the grease line but I do not...
View ArticleLive tool max spindle speed parameter Fusion 640T, SQT250MY
We have a SQT250MY with a fusion 640T control. The live tooling should go to 4500 rpm but it maxes out at 2000 rpm. Called mazak service a few times and they said I need to change some parameters but...
View Articlenew tool eye install HOW TO? integrex 400-4s
good morning everyone. i just had my tool eye sensor swapped out for a new one. but i have a problem, i can physically install it but how do i set it/or calibrate it ? machine is a MAZAK integrex...
View ArticleIntergrex e500H2 - Seiki file management 'best practice'?
Good morning, We have a Integrex e550h2 with a Matrix 2 control. Currently all programs are transferred via USB but we shortly have Seiki coming in to visit us and install Seiki on our networked...
View ArticleHow to turn on high oressure coolant in Mazatrol prog VTC250D/50 with a...
Hi folks. Machine is equipped with high pressure coolant and has never been used. I know M131 turns it on and is regulated with (I think M103-M107). Trying to make it come on in a Mazatrol prog and...
View ArticleFor anyone that wants to put a probe setup on their Mazak 640M control
I purchased a 2002 VTC-200C several months ago, its an awesome machine for a price i couldnt pass up. The only downer is the machine did not have a probe in it. Mazak quoted me at 15k to install one...
View ArticleMazak QT20 T1 CPU error
Hi I have a mazak QT20, with T1 controller and it has a CPU 3 error. Initially it said I have a WD error, I hope someone can help me with this. Waznik72
View ArticleMazatrol users-Anyone use tool presetters?
Looking at getting a Speroni tool presetter for our shop. Mostly for our milling department, but management would like to be able to use it on our Intergrexes. We run exclusively Mazatrol programs on...
View ArticleClik here to view.
Mazak nexus 510c-ii e stop alarm
Came in this morning and fired up my machine. I was able to home the machine and jog it to take a fixture off my rotary axis. When I tried to put the new fixture back on I was getting an alarm on my...
View Article