Integrex C Axis Sync
We have an Integrex 100-IISY with fusion conrol. I am trying to figure out how to bring the sub up and sync the C axis on the main and sub so I can mill with part clamped in the main and sub spindle. I...
View ArticleNeed to quote some 304 ss lathe job, tap or single point 3/8 bsp?
Hi, I need to make 400 end caps with a 3/8 bsp thread in 304 ss. should I single point cut the threads or use a tap? If I use a tap it will be 2 ops. Also any recommendations on brand of tap and/or...
View ArticleClik here to view.
M32 on H1000 Wont Take Programs
I'm having issues with uploading programs to our H1000 we just picked up. We use Calmotion USBCNC boxes to upload to our machines using a USB stick. (USBCNC - Calmotion) For some reason the control...
View ArticleCoolant Start
Mazatrol program on a T-Plus control. I have non cutting tool that I use for a work stop. My first line is a "MNP" process with a G00 with my x, y data and a M00 program stop. The next line is then a...
View ArticleMazak 216 Alarm
I have a new to me 1989 Mazak QT15 with T2 Control. I do not know the history or previous working order as i bought it at a auction without power hookup. It looks like i need to finish registering...
View ArticleMazak slant turn 20-atc mazatrol t32-3 EIA/ISO?
Hello quick question I was wondering if there is a way of activating EIA/ISO option for this machine? there is a cassette in the back that says EIA/ISO, but I don't know if I can turn it on thanks in...
View ArticleHow do you arrange your coolant tubing on your lathe ?
Quick turn smart 200M: On most of the outside turning tools the jets on the bolt-on holders works fine and hits their target, but on boring bars and groove tools with threads on the back (for...
View ArticlePFH4800 M codes
I have searched the archives, to no avail. I am looking for an M code list for a Mazak PFH4800. 2005 model with a 640M control. Just a list for the 640M control would probably help.
View Articletrying to cut a worm shaft on 200 matrix II issues
My first post, would appreciate some wisdom that this forum has from reading a while. Long story short; I run an old QT15 and the other machine next to me is a newer 200. The place that I work for...
View ArticleM32 Ladder edit
We have a M32 control on a horizontal mill. Sometimes the tool change door will close after a tool change but the coolant will not turn on. The machine will keep going through the program with no...
View ArticleSQT18 M T32-3 good or not
I am looking at a 1994 SQT18M with a T32-3 control. I have always programmed in EIA in the past. I really am looking for any input of the control more than anything. Are they good? Bad? And can I get...
View Articlemazatrol t32 153 z offset not found??
I'm getting an alarm 153 z offset not found wen I try to run program. I looked in the books but I can not find why I'm getting that msg. I touched off on my work piece can't seem to get Tool eye...
View ArticleIssues with my 95 model QT-20 again T Plus control
First issue that has been a PITA is cross slide lube alarm. At random times, mostly in middle of a cycle, I get the cross slide lube alarm. When alarm is on, pump motor is still running, you can see...
View ArticleVoltages and Phasing - SQT 18MS
Measured the voltage supplying a 30hp Phase Perfect yesterday and it was 238 to 240. Today I measure and it's 248v which means the lathe transformer is putting out 207 to 208. The machine wants 200v...
View ArticlePlease help confirm parts needed
My QT6T turret recently started leaking hydraulic fluid on cold startup. The leak stops after a few lock/unlock cycles and when the oil warms up. Leak doesn't return until next cold start. This can...
View ArticleClik here to view.
2 Issues - Control freezing on startup, B axis not homing - SQT 18
Have the power to the lathe, turn the big switch, then when I press the power button the control tries to come on but often doesn't for 5 or 6 cycles through power on/off using the shutdown button...
View ArticleSimple Lathe Question
I have a few parts to make that are about as simple as it gets. But the problem is that they are made from 6061 and the finish diameter is .255 +-.001 and a length of 1.950". So I'll have to start with...
View ArticleM2 Auto off?
It's there an auto off (after x amount of minutes of no action etc.) Option somewhere in the m2? I've recently moved into a factory where i can run unattended into the night, however i would like for...
View ArticleClik here to view.
Quick Turn Smart turret/base alignment
Machine: Quick turn smart 200M. Well, I heard everyone crashes their lathe sooner or later and on the last job it was my turn: It was a really stupid mistake (maybe all crashes are stupid ?). I was...
View ArticleVTC 20B - Pneumatic Counterbalance
Yesterday our VTC 20B had been running all day without an issue. A job was changed over and the machine was started, As it moved Z in rapid we got a Z axis excess error. After examining the problem in...
View Article