MAZAK SQT10 MSY T-plus
Been searching all over the net for a MAZAK SQT10 MSY with T-plus mid 90's Did Mazak ever made that model with Y axis and a sub or they only did the MS version?
View ArticleVQC 20/50 20 NMI emergency stop
As in the title I have had this error coming on for the last few days. Have tried disconnecting different things but cant get rid of it. I had this a few weeks ago and turned out it was the tool setter...
View ArticleClik here to view.
Mazak QT15 Turrent Removal
I need to allign my turret. I am tired of having little nibs in the middle when facing off. I have read as many posts as I can find on here. I tried to put a big bar in and still can't get it to center...
View ArticleMazak SQT10MS - 201 breaker trip alarm
OK... So I have 2 of the identical machines. The other is down right now with a servo lag excess alarm. That one on a different post..ahhh..take a breath. So I finally get this machine running a job...
View ArticleVariaxis 5 axis coordinate setup
We have a VRX i-700. We've always used it for 3+2 work using the WPC shift in Mazatrol. We want to try some full 5 axis work. I think that I need to do some type of compensation of the workpiece...
View ArticleClik here to view.
Oil or grease in live tool holder.
My live tool holders (NACHI PB7130) to my SlantTurn 30 ATC is noisy. So my plan is to put in new bearings and seals. What I dont know is if it should be oil or grease in these and how much. I have...
View ArticleClik here to view.
Mazak SQT10MS Live Tooling
Hi we're looking to buy some more driven tooling for our 10MS. Our current tooling has a 40Dia x 60mm shaft with a recessed drive tongue. All the tooling I can see on ebay has a 70mm long shaft with a...
View ArticleVqc 20/40 coolant annoyance
Hey guys, So amongst many other short comings of my vqc (it's so oooooollllddd! [emoji14] i want all the features of a new fancy machine!) Something that's been annoying the shit out of me lately is...
View ArticleTool Path Check Question
Is there any way to pan around in the Tool Path Check Viewer? I'm doing some detailed machining on a part that is 5" Diameter and I understand how to zoom in, but I can't figure out how to pan so I can...
View ArticleClik here to view.
Looking for guidance on programming road block
I put 5 hrs into trying to figure it out and no luck. Mazak QTN-100 Mazatrol Matrix Nexus Fusion control. Im trying to do a back turn of sorts so I can machine a .25 Semicircle in one work holding so...
View ArticleV515 QX524 Card Repair
Our 95' V515 mill has a problem with the QX524 board. With initial startup none of the motors will come on and we get a black screen with red lettering (PlC Op. Chip Error). The 524 board leds show it...
View ArticleQT8N spindle problem
Its time to call in for some advice because I'm running out of ideas..........I bought a real clean QT8N with T Plus control from a Vo-Tech that absolutely looks new, it was in storage for 7 years...
View ArticleClik here to view.
M32 42 Parameter error
Hi All, I have Mazak AJV 18 that was disconnected for over 4 months and we just powered it back up and installed new batteries we followed the procedure from...
View ArticleTouch sensor acting weird in Mazatrol
I am using a mazatrol program on a VTC800 (five axis) to probe a part held in the c-axis (rotating about x). I am picking up two datums along the x axis, and then bringing the b axis up to 90 degrees...
View Articlemazak vqc15/40 with pallet changer parameters needed
my floppy drive died . got new usb floppy from Mitsubishi and loaded param and system files . but no go .parameters must be wrong . anyone have parameters for vqc15/40 with pallet changer? thinking its...
View ArticleTPlus- Setting turret index position.
Hey All, Got a bit a problem. I'm machining a 7" long piece sticking out of the chuck with a boring bar and drill sticking out about 5" from the turret. For some reason the machine likes to index about...
View ArticleIntegrex Matrix 2 - Alarm 1443- Backup Incomplete
Upon startup, I get alarm 1443-Backup incomplete -999, -1, 3 Sounds serious. Sometimes, at power down, Windows does not want to close and says something about a virtual driver not shutting down. How...
View ArticleMazak quick turn 8 SP
I just recently acquired my first cnc machine a very clean 1986 Mazak QT 8 SP the machine set for 6 years without power so it lost memory, I have replaced the batteries and started entering parameters...
View ArticleFR-SE 2-22K Converter Over Voltage
Had this alarm on 3 occasions over the last week or so, power down and re-start gets me going again, any of you guys had this happen to you? It usualy happens on deceleration, machine goes into E-stop...
View ArticleAdding EIA to T2 mazatrol
Hi, I know this has been discussed before and some of you have tried to add EIA to your mazatrol and it hasn't worked but I'm a bit thick and would like to have a crack at getting it working. Does...
View Article