Clik here to view.
Higher millspeed on my QT10ATC
I bought an QT10ATC M/C T3 -86 a few mounths ago and was a little bit dissapointed at the mill speed. My ST30ATC M/C T3 -88 has 3000rpm on the mill head but this QT10ATC only did 1500rpm. That was a...
View ArticleClik here to view.
OD grooving cycle #1 problem mazatrol T2
Hi, I'm suffering with a grooving problem. Making a grove with starting 3mm radius start-x 80. start-z 10. end-x 70. end-z 10 endradius 3. When you do check toolpaths it all seems normal it does rough...
View Article200 Thermal Trip Alarm - SQT 18MS
Had her humming along nicely when it threw a 200 thermal trip(emergency stop) alarm. Control is on, machine is pretty much dead. Hydraulics, most fans, and coolant pumps off. Checked all...
View Articleprogram transfer
Anyone used one of these? FTDI USB Mazak Mazatrol CAM Fusion Nexus CNC DNC Cable Software Flow Control | eBay
View ArticleNexus 51c owners maintenance items to check out.
We own 4 of these machines and have had them for several years. We have time now to do a deep P.M. and cleaning on them. We have found on all 4 machines the grease hose that runs on the back side of...
View Article640T Lathe Alarm 26 Illegal parameter
Guys, I have alarm 26 illegal parameter on my 640T lathe what causes this and how do I reload parameters if necessary? It looks like the battery died over the weekend so I am assuming this is the cause...
View ArticleHow to activate parts counter in EIA mode Mazatrol Matrix Nexus 2
Hi folks! After spending a career in front of Fanuc based machines, I am now tasked with learning the Mazak. I have a few questions and will break them up into separate entries here. First off, the...
View ArticleCan someone educate me on "Additional WPC's" Mazatrol Matrix Nexus 2
Hi folks! After spending a career in front of Fanuc based machines, I am now tasked with learning the Mazak. I have a few questions and will break them up into separate entries here. First off, the...
View ArticleNeed assistance with "Bed Wash" VTC250D/50 with a Mazatrol Matrix Nexus 2
Hi folks! After spending a career in front of Fanuc based machines, I am now tasked with learning the Mazak. I have a few questions and will break them up into separate entries here. First off, the...
View ArticleRe-threading on SQT with T-Plus control HOW?
I am trying to figure out how to enlarge a thread on the lathe. I am new to CNC lathes. This is only my 2nd day actually running a CNC lathe. Unfortunately I sold my manual lathe which I know how to do...
View ArticleClik here to view.
Align turret on a QT10ATC (1986) T3
Anyone know how to align the turret in "Y axis" on a QT10ATC (1986) T3. The machine does not have any Y axis but is 0,3mm of in that direction. The seat for the VDI40 is new. Is it possible to align...
View ArticleClik here to view.
Extra guarding on vqc20/40a
Has anyone added some extra guarding to a vqc? I want to stop all the coolant shooting out the top making a mess on my already messy floor. Sent from my LG-H815 using Tapatalk
View ArticleMazak QT-8 with CAM-T2 control. Looking for service manual
I'm a newbe to the forum and also Mazak. I just bought a QT-8 lathe and I am wondering if someone might have a digital copy of the service manual and wiring schematic for this machine. Or one they...
View ArticleHow to reset the clock on a Mazatrol Matrix Nexus 2
The control is not connected to the web so it doesn't know the real time. How can I set it manually? It's running 6 minutes fast and is very annoying. Especially at breaks and lunch LOL Thank you! Mark
View ArticleMazak Slant Turn 30 ATC-MC
Hi....wondering if someone can help. We have a Mazak, Mazatrol CAM T-3, Slant Turn 30 ATC-MC. There is an intermittent problem with the spindle stopping when it changes gears (maybe 10-12 times a day)....
View ArticleMazak Matrix Pocket agreement.
Hi All, This is my first post on PM. I appreciate all the information I have gotten here over the years. Here is my question. I have a 510C-II VMC that the control and magazine pocket number does not...
View ArticleOrings for vdi tools
Does anyone know offhand what size Orings are on the vdi 40 tooling. This is on the stem and the coolant. I need to order some but won't be back until Wednesday to measure. Thank you in advance.
View ArticleVTC250D/50-Mazatrol Matrix Nexus 2 Can I use the spindle probe to find G54?
Hi Folks. I can use my spindle probe to find WPC's, but not G54, etc. I call up a Maz program, find my X, Y, and Z, write down the numbers, then physically input them into a G54. Thinking there has to...
View ArticleTrouble with G68.2 and rotary table on VTC800
Our machine shop is currently using a Mazak VTC 800 in an unusual configuration - the rotary table is unmounted and unused. We are currently attempting to machine a part at 45 degrees (in G code...
View ArticleMazak A16 megaturn
Hi, our A16 is a T3 control and I'm looking for some details on alarm number 31 that is displayed on the tool magazine display as the alarm list in the maintenance manual only goes to 24. The...
View Article