Mazak HQR 100 Problem after transfer from sp1 to sp2
Hello there , before few weeks we recived our new machine HQR 100 and i started do a program for very simple workpiece. First days was a bit hard ,becouse of some parameters (su112 , su117 etc) , and...
View ArticleMazak 18 manual lathe - feed gearbox oiling
I have just bought this lathe. I can see oil circulating in the headstock sight glass, but I can't see oil circulating in the feed gearbox sight glass. There is oil in the gearbox, according to the...
View ArticleMachine powered or not when changing batteries?
Should the machine be powered on or off when batteries? Its a T32-6 and it has: 1pcs 6v 20Ah 3 NicCd 3,6v 250mAh (one on the control and 2 on the X Z C drive)
View ArticleM32 887 Tape I/O error
Hi all, I scoured this forum for 877 errors on M32 controls but could not really get good posts. I have the same problem on two different machines: AJV-18 Vertical Mill H400 Horizontal Mill Both M32...
View ArticleClik here to view.
Mazatrol help
Hi All, I am wondering if any of you smart folks can help me find a way to do this. Attached is a picture of part geometry and a rough looking tool for a part I am about to make. I would like to use a...
View ArticleT1 Optional Stop Question
I've done some searching and it looks like this one may be half beaten to death, but no resolution exactly. One of the guys I work with is running an '82 vintage Slant 15 with T-1 controls. He's...
View ArticleMAZAK QX084 card
Mazak QX084 card, thats the one with the battery, how much time do i have to swap the whole card before all parameters go poof :ill:
View ArticleClik here to view.
Anyone have a straight live tool for a Multiplex 620 for sale?
Hi I am looking for a straight live tool for my Multiplex 620. It should be ER32 or a floating tap holder. It should look like this: (But this one is a ER25) Attached Thumbnails Â
View ArticleMazak QT15 problem
I have a QT15 with a T2 controller. It has been running perfectly and run every day for the last three weeks. Turned on the next morning following a day of running and the computer was scrambled. It...
View ArticleMazak QTN100-2 Tool Nose Radius Compensation Question
Fusion Matrix control Ever since I got my lathe I struggle making correct radii on smaller features (i.e. .015R on a .250 Dia). Well I'm trying to turn a 4° taper to 0,0 and I'm getting an approx .020"...
View ArticleDoes anyone hard turn on older Mazaks?
I have some products I'd like to get into that involve hard turning 3" D2 @64rc on a 96' SQT15MS. My spindle isn't the greatest, so I'll likely have it rebuilt after the holidays. Theres no backlash in...
View ArticleT1 Tool life alarms... Any way to disable?
My quick turn 10 with T1 control gives me alarms when tool cutting time exceeds tool life time. Is there any to disable this? Some parameter maybe? Thanks
View ArticleGood replacement of T32-6 floppy drive?
So far we have been running T2 and T3 machines in our workshop, now we bought a MultiPlex 620 with T32-6 controler. And its reading from the floppydrive if the battery is out of power. I have changed...
View ArticleClik here to view.
What model is this Mazak?
I just bought this on a whim at an auction this week. Curious as to opinions of this vintage and just what model is it? Swings roughly 34" over the bed and has 14 feet between centers. I spoke to the...
View ArticleAny way to skip finishing sequences on mazatril t plus
In mazatrol t plus is there any way to skip finishing sequences? I am spending to much time doing finishing on places that are going to be machined in following operations?
View ArticleClik here to view.
QT-10N Turret Bearing replacement - Radial Play / turret misalignment question.
I'm doing the bearings in the turret (I'll elaborate on why below)... I purchased a pair of the two big bearings NTN 6013-ZZ and NTN 6013-ZZNR that it rotates on. I also grabbed new thrusts for the...
View ArticleQuick Turn 8N x axis carriage alignment?
Hello everyone, I have just acquired a 89 QT8. I see the carriage is out of alignment in the X axis. The turret is aligned with the spindle bore fine, but I can get .002" out if I sweep the face of the...
View ArticleClik here to view.
Servo noise?
I have a new to me MultiPlex 620 that is now up and running after som minor issues. But my left side axis (both X and Z) are making a noise when moving. I tried to add oil to ballscrew and slides but...
View ArticleConversational Programming
Good morning everyone!!! Are there any sites to learn conversational programming? Can you do this with CAM or does this have to be done at the machine? I am just interested in learning something in my...
View ArticleQT-15 x-axis twist
Hi, How much twist in the x-axis stroke is "ok"? The machine qt15 1988 Acording to the precision level its 0.1mm @ 1meter. Moves 5 points on a 0.02mm/m level. Its a railguide machine so that much wear...
View Article