st20-atc maintenance manual
Hi, does anyone know where I could obtain a copy of a ST20-ATC maintenance manual, typically it's the one manual that did not come with the machine and the one manual I need the most right now.:cryin:
View ArticleClik here to view.
How to program this part on my t-2?
Hello Philabuster and Company. I've got a part I'm having trouble with. It's got a flat bottomed feature inside this big id dish, and I have had trouble making this from solid. The trouble is getting...
View ArticleRenishaw Probe Replacement - Mazak HCN-4000
Hey Everybody, I have a 2008 HCN 4000 II with a Matrix control. We bought it used, and it didn't come with the part probe. It was described as fully prepped for an MP10 Probe. The previous owner...
View ArticleGetting a demo on a Mazak 530C, any input on this machine???
Attending a demo later this week on a new Smart 530C. Not sure if its a nexus though, nor do I know the difference. We have absolutely NO experience with Mazak, so any input will be greatly...
View ArticlePROBING in EIA for mazak vtc 250-50 mill ?
havign a hard time probing 4 operations in my set up cant even get the 1st going.. 1st one is i am trying to probe my z offset in g54 and my x offset from the center of the part N100 N1G91G28Z0....
View ArticleHow do you set face grooving tools on T1?
Do you set face grooving tools from the od, id, or center? I do face grooves so infrequently I have to start over figuring it out each time and just mess with the offsets until I get it. The numbers...
View ArticleMad Mazak
Dear Fellow Mazak Nuts . I have a question for the computer experts? Is there a device to transfer Data from a R32 Port on older machines to a thumb drive for the newer Mazaks.
View ArticleMazatrol Synchronous Z movement?
I need to do some Synchronous Z movement to soften an edge with a ball end mill. Is there any way to do this effectively in Mazatrol? I never used the manual program before. For anyone feeling...
View ArticlePart Runout
I am facing and boring my parts on head one the clamping by ID on head two. When I check the ID is it not concentric by .004 TIR. My jaws are skim cut after I put them so I know they are good. Any...
View ArticleClik here to view.
Thread Mill Face on Live tool Lathe using Mazatrol (C-axis)
Is there a way in Mazatrol to program a helix in the face the of part to produce threads (Thread Milling) with out a Y-axis. We have a QTN-250M with Matrix Control. I was told this can't be done...
View ArticleLive Tool Engraving On a T32-3 Control
I figured I'd put this in another thread as the SQT18-MS Issues thread had a lot of other information in it. Basically, I need to engrave part numbers on the face of my work. I have the CNCWrite...
View ArticleMazak integrex tool arm home
I have an integrex 200-3s I had a problem with a tool change and I think I accidentally changed the tool arm home location. When a tool tries to go into the spindle and the side shifter it jams. The...
View ArticleVDI tooling question
Hi guys. I've got a mazak qtn msy 200 and I'm looking to buy some radial live tooling for it. Found a VDI 40 from a company called EWS. First of all, will it fit? The shanks for the tools in my machine...
View ArticleMazak Quick Turn 10 FR-SX Spindle Drive Diagnosis
I just powered up our new-used Quick Turn 10 with the FR-SX spindle drive. I have a problem with the spindle drive. Any trouble shooting advice would be appreciated. Here are the symptoms: -Won't run...
View ArticleBoring away from chuck T-2 control
I have an aluminum part with .540" blind bore about 2.25" deep. I'm using a 3/8" solid carbide bar and I was thinking I'd like to make the finish pass away from the chuck to avoid the chips burying in...
View ArticleMazak SQT15M questions
We're finishing the install of our new to us SQT15M and have a couple of quick questions. 1. The leveling procedure in the manual is vague at best and show some type of jig that looks like it get...
View ArticleQT 30 dual turret down, blinking cursor ONLY on screen! HELP PLEASE! !
My QT 30 , is only showing a blinking cursor on the screen, have checked all fuses, all power checks good, no apparent alarms that I see. Thinking may need to reinitialize, ,, ANY HELP WOULD BE...
View ArticleStandard tooling package SQT15M
I'm missing one tool holder and trying to figure out which one it is. Looked in the mechanical parts manual but can not find any part numbers for what is included as part of the "standard tooling...
View ArticleClik here to view.
Live tool tapping SQT15M
Looking for a right angle tapping holder (tapping on the face of the part using C axis) the previous owner was using a Mazak #53628010101 holder that I have been unable to find any info with a Google...
View ArticlePricing Mazak V-414/22
Mazatrol M32B Older machine, probably 20 years old? In decent shape, operator says he can still hold .02mm without too much trouble. 30 tool magazine 22x16 or so of travel. So the machine is where I...
View Article